Air Tool Lubricants

Syngard

Syngard synthetic air line lubricants are formulated from the highest quality, synthetic fluids available and fortified with an additive system designed for the most demanding air tool applicators. Syngard is available in both ISO 32 and ISO 68 viscosities to accommodate both small and large air tools.

Lubeair

Lubeair air line lubricants are high-quality lubricants specially formulated for the most demanding air tool application. There are two grades, Lubeair-32 and Lubeair-68, to handle both small and large heavy-duty applications.

• Lubeair-32 is for small drills, grinders, vibrators, wrenches, screw drivers, air nailers and staplers, air cylinders, motors, valves and chucks.

• Lubeair-68 is for large drills, grinders, vibrators, hand-held tools and jackhammers.

Lubeair lubricants are a special blend of catalytically hydrogenated, solvent refined, paraffin base stocks with very low pour points. Special additives have been blended with the base stock to enhance its physical properties and provide the following benefits:

• Emulsification of the moisture in the compressed air to prevent rust.

• Tough extreme pressure properties to protect tools from seizure and wear and provide good adherence to wet working surfaces.

• Resistance to oxidation to prevent lost time due to gumming and varnishing.

• Proper atomization for good lubrication and proper control of fogging.

Top of page

Gas Turbine Lubricants

SH^®-32T and SH^®-46T

Summit SH^®-32T and SH^®-46T Gas Turbine Lubricants have been formulated to operate in land-based gas turbines under a wide range of temperatures. Synthetic hydrocarbon base stocks and selected additives combine to provide excellent viscosity-temperature characteristics, oxidation stability, wear resistance, and load-carrying ability.

Summit Gas Turbine Lubricants meet the requirements of specifications approved by all of the major manufacturers of gas turbines and Summit SH^®-32T is approved by Solar Turbine as conforming to their ES9-224 lube oil specification for Class I ISO 32 lube oils.

Top of page

Vacuum Pump Lubricants

SHV

Summit SHV Series is formulated from vacuum distilled ultra-pure synthetic hydrocarbon base stock to provide an extremely low vapor pressure vacuum pump lubricant.  These non-foaming fluids have excellent water separation and provide protection against wear, rust and corrosion.  The SHV Series is an extended life lubricant designed to function in applications subject to severe temperature and environmental conditions.

Available as:  SHV-15, SHV-22, SHV-32, SHV-68, SHV-100

Top of page

PSV-22

Summit PSV-22 is formulated from a vacuum distilled ultra-pure paraffinic hydrocarbon base stock to provide an extremely low vapor pressure vacuum pump lubricant.  This non-foaming fluid has excellent water separation and provides protection against wear, rust and corrosion.  The PSV-22 is an extended life lubricant designed to function in recirculating systems such as liquid ring vacuum pumps which are subject to severe temperature and environmental conditions.

Top of page

Heat Transfer Oils

Thermoyle HT

Summit Thermoyle HT was designed to meet the tough thermal demands placed on high temperature heat transfer mediums. The synthetic hydrocarbon base stock is well suited to combat the problems of carbon formation on heated surfaces and decreased fluid life as is commonly encountered with conventional petroleum-based fluids without exhibiting the hazardous characteristics found in aromatic heat transfer fluids. The additional benefits of an extremely low vapor pressure and sub-zero pour points allow for increased efficiency while reducing pressure build-up and evaporation losses:

USER BENEFITS

• Exceptional thermal stability - resistant to coking and oxidation

• Long operating life

• Low volatility

• Non-toxic

• Superior thermal conductivity

• Low pour point

• Wide operating range

Available as: Thermoyle 50 HT, Thermoyle 100 HT, Thermoyle 200 HT

Top of page

Rotary Screw Varnish Cleaner

Varnasolv

The use of petroleum lubricants, primarily automatic transmission fluid (ATF), in rotary screw and rotary vane compressors results in the formation of varnish and carbon. The varnish and carbon is deposited throughout the system and can cause a number of serious operational problems, resulting in excessively high maintenance costs.

Summit's Varnasolv can help alleviate the problems caused by varnish and carbon. Varnasolv is designed to be used as an additive in the lubricant to remove and suspend varnish while the compressor is in operation. Using Varnasolv eliminates the need for disassembling the compressor for cleaning. For maximum benefit, use Varnasolv prior to each lubricant change.

Top of page

The information contained in this document is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability.