|
Syngard
Syngard synthetic
air line lubricants are formulated from the highest quality, synthetic fluids
available and fortified with an additive system designed for the most demanding air tool
applicators. Syngard is available in both ISO 32 and ISO 68
viscosities to accommodate both small and large air tools.
Lubeair
Lubeair air line lubricants
are high-quality
lubricants specially formulated for the most demanding air tool application. There are two
grades, Lubeair-32 and Lubeair-68, to handle both small and large heavy-duty
applications.
-
Lubeair-32 is for small drills, grinders,
vibrators, wrenches, screw drivers, air nailers and staplers, air cylinders, motors,
valves and chucks.
-
Lubeair-68 is for large drills, grinders,
vibrators, hand-held tools and jackhammers.
Lubeair lubricants
are a special blend of catalytically hydrogenated, solvent refined, paraffin base
stocks with very low pour points. Special additives have been blended with the base stock
to enhance its physical properties and provide the following benefits:
-
Emulsification of the moisture in the compressed air to
prevent rust.
-
Tough extreme pressure properties to protect tools from
seizure and wear and provide good adherence to wet working surfaces.
-
Resistance to oxidation to prevent lost time due to
gumming and varnishing.
-
Proper atomization for good lubrication and proper
control of fogging.
Top of page
SH®-32T and
SH®-46T
Summit SH®-32T and SH®-46T
Gas Turbine Lubricants have been formulated to
operate in land-based gas turbines under a wide range of temperatures. Synthetic
hydrocarbon base stocks and selected additives combine to provide excellent
viscosity-temperature characteristics, oxidation stability, wear resistance, and
load-carrying ability.
Summit Gas Turbine Lubricants meet the requirements
of specifications approved by all of the major manufacturers of gas turbines and Summit
SH®-32T is approved by Solar Turbine as conforming to their ES9-224
lube oil specification for Class I ISO 32 lube oils.
Top of page
SHV
Summit
SHV Series
is formulated
from vacuum distilled ultra-pure synthetic hydrocarbon base stock
to provide an extremely low vapor pressure vacuum pump lubricant.
These non-foaming fluids have excellent water separation
and provide protection against wear, rust and corrosion.
The SHV Series
is an extended life lubricant designed to function in applications
subject to severe temperature and environmental conditions. Available
as: SHV-15, SHV-22, SHV-32, SHV-68, SHV-100
Top of page
PSV-22
Summit PSV-22
is formulated from a vacuum distilled ultra-pure paraffinic
hydrocarbon base stock to provide an extremely low vapor pressure
vacuum pump lubricant. This
non-foaming fluid has excellent water separation and provides
protection against wear, rust and corrosion.
The PSV-22 is an extended life lubricant designed to function in
recirculating systems such as liquid ring vacuum pumps which are
subject to severe temperature and environmental conditions.
Top of page
Thermoyle HT
Summit Thermoyle HT was
designed to meet the tough thermal demands placed on high temperature heat transfer
mediums. The synthetic hydrocarbon base stock is well suited to combat the problems of
carbon formation on heated surfaces and decreased fluid life as is commonly encountered
with conventional petroleum-based fluids without exhibiting the hazardous characteristics
found in aromatic heat transfer fluids. The additional benefits of an extremely low vapor
pressure and sub-zero pour points allow for increased efficiency while reducing pressure
build-up and evaporation losses:
USER BENEFITS
Available as: Thermoyle 50 HT, Thermoyle 100 HT,
Thermoyle 200 HT
Top of page
Varnasolv
The use of petroleum lubricants, primarily automatic
transmission fluid (ATF), in rotary screw and rotary vane compressors results in the
formation of varnish and carbon. The varnish and carbon is deposited throughout the system
and can cause a number of serious operational problems, resulting in excessively high
maintenance costs.
Summit's Varnasolv can help alleviate the
problems caused by varnish and carbon. Varnasolv is designed to be used as an
additive in the lubricant to remove and suspend varnish while the compressor is in
operation. Using Varnasolv eliminates the need for disassembling the compressor for
cleaning. For maximum benefit, use Varnasolv prior to each lubricant change.
The information contained in this document is the result of
careful testing in our laboratories, complemented by selected literature. It does not in
any way constitute a guarantee, nor does it serve as a license to operate any patent. Due
to widely varying conditions of product use, which are beyond our control, it is strongly
recommended that the product be tested for suitability.
Top of page
The information
contained in this document is the result of careful testing in
our laboratory, complemented by selected literature. It
does not in any way constitute a guarantee, nor does it serve
as a license to operate any patent. Due to widely
varying conditions of product use, which are beyond our
control, it is strongly recommended that the product be tested
for suitability.
|
